marlio

AP Physics 1, Unit 8

Exam words: Fluids

The 36 words a written answer in this unit needs. For each one: what it means, a wording that loses the mark and why, and a sentence that uses it the way a full answer would.

Study these words as a deck

Flashcards, Learn, Test and Match in Cards, with your Still learning marks kept, and the booklet to print on A4 or US Letter. Sign in to open it.

The words

  1. density

    ρ=m/V\rho = m/V · Units: kg/m³

    The mass per unit volume of a material, in kg/m³.

    Loses the mark: “dense means heavy”. A big light object can weigh more than a small dense one; density is mass per volume.

    Example: The density of the aluminum block is 2700 kg/m³ whether I measure the whole block or a chip of it.

  2. average density

    An object's total mass divided by its total volume, including enclosed air.

    Loses the mark: “steel is lighter than water”. Steel is denser than water; the hollow hull lowers the average density.

    Example: The steel ship floats because its average density, hull plus the air inside, is less than that of seawater.

  3. pressure

    P=F⊥/AP = F_\perp/A · Units: Pa

    The perpendicular force per unit area, a scalar in pascals.

    Loses the mark: “pressure only pushes down”. Fluid pressure pushes on a surface from every direction, perpendicular to it.

    Example: The 600 N student on snowshoes of total area 0.2 m² exerts a pressure of 3000 Pa on the snow.

  4. pascal

    Pa · Units: N/m²

    The SI unit of pressure, one newton per square meter.

    Loses the mark: “newtons of pressure”. Pressure is in pascals, newtons per square meter, not in newtons.

    Example: Atmospheric pressure is about 101,000 Pa, and each pascal is one newton on every square meter.

  5. average pressure on a wall

    Units: Pa

    The force on a vertical wall equals the pressure at half depth times area.

    Loses the mark: “bottom pressure times the whole wall area”. Pressure is smaller nearer the surface, so this doubles the force.

    Example: The average pressure on a wall of the 2 m deep tank is ρg(1 m), so the force is half of ρg(2 m) times the area.

  6. pressure at depth

    P=P0+ρghP = P_0 + \rho gh · Units: Pa

    In a static fluid, pressure at depth h is surface pressure plus ρgh.

    Loses the mark: “a wider tank has more pressure at the same depth”. Pressure at a depth depends only on ρ, g and h, not on the container's width.

    Example: The pressure at depth 3 m in the pool is atmospheric pressure plus 1000 × 9.8 × 3, about 29 kPa above it.

  7. free surface

    The open top of a liquid, where its pressure equals the air pressure.

    Loses the mark: “measure h from the bottom of the tank”. h is depth below the free surface, not height above the floor.

    Example: The free surface of the lake is the reference, so h = 4 m for the diver 4 m below it.

  8. gauge pressure

    Pgauge=Pabs−PatmP_{gauge} = P_{abs} - P_{atm} · Units: Pa

    Pressure measured relative to atmospheric pressure, the absolute pressure minus atmospheric pressure.

    Loses the mark: “add atmospheric pressure to everything”. For net forces on walls open to air, the atmosphere acts on both sides and cancels.

    Example: The tire gauge reads a gauge pressure of 220 kPa, so the absolute pressure inside is about 320 kPa.

  9. absolute pressure

    Pabs=Pgauge+PatmP_{abs} = P_{gauge} + P_{atm} · Units: Pa

    The total pressure measured relative to a vacuum, equal to gauge pressure plus atmospheric pressure.

    Loses the mark: “absolute pressure at the bottom is just rho g h”. An open container also has the atmosphere pressing on its surface.

    Example: At the bottom of the open 2 m tank the absolute pressure is 101 kPa + 19.6 kPa, about 121 kPa.

  10. atmospheric pressure

    PatmP_{atm} · Units: Pa

    The pressure of the air at a location, about 1.01 × 10⁵ Pa at sea level.

    Loses the mark: “the air only presses down on us”. Air pressure acts in every direction, so it pushes up and sideways too.

    Example: Atmospheric pressure pushes up on the card under the inverted glass of water as well as down on the outside.

  11. Pascal's principle

    A pressure change in an enclosed fluid is transmitted undiminished to every part of it.

    Loses the mark: “the pressure is bigger at the big piston”. The pressure is the same at both pistons; the force is bigger because the area is.

    Example: By Pascal's principle, pressing the brake pedal raises the pressure equally at every brake caliper.

  12. hydraulic lift

    F1/A1=F2/A2F_1/A_1 = F_2/A_2

    Two pistons joined by enclosed fluid, so force ratio equals area ratio.

    Loses the mark: “the lift multiplies the energy”. The small piston moves farther in the same ratio, so work in equals work out.

    Example: The hydraulic lift's large piston has 50 times the area, so 200 N on the small piston lifts 10,000 N, moving 1/50 as far.

  13. buoyant force

    FB=ρfVdispgF_B = \rho_f V_{disp}g · Units: N

    The upward force a fluid exerts on an immersed object, equal to displaced fluid's weight.

    Loses the mark: “the object weighs less in water”. Its weight is unchanged; the buoyant force supports part of it.

    Example: The buoyant force on the 0.002 m³ submerged stone is 1000 × 0.002 × 9.8, about 20 N, at any depth.

  14. Archimedes' principle

    Buoyant force on an object equals the weight of the fluid it displaces.

    Loses the mark: “it displaces its own weight of water”. That is true only when floating; a submerged object displaces its own volume.

    Example: By Archimedes' principle, the crown displaces 0.0001 m³ of water, so it feels a 0.98 N buoyant force.

  15. displaced volume

    VdispV_{disp} · Units: m³

    The volume of fluid pushed aside by the immersed part of an object.

    Loses the mark: “the volume of the whole object always”. For a floating object only the submerged part displaces fluid.

    Example: The displaced volume of the half-submerged ball is half its total volume, 0.5 L.

  16. floating condition

    FB=mgF_B = mg

    An object floats if its average density is less than the fluid's.

    Loses the mark: “heavy things sink and light things float”. Floating depends on average density compared with the fluid, not on weight.

    Example: The floating condition holds for the 600 kg/m³ log in water, so it rises until the buoyant force equals its weight.

  17. submerged fraction

    Vsub/V=ρobj/ρfluidV_{sub}/V = \rho_{obj}/\rho_{fluid}

    The fraction of a floating object's volume below the surface.

    Loses the mark: “melting ice cubes make the water level rise”. Floating ice already displaces its own weight of water, so the level is unchanged.

    Example: The submerged fraction of ice in fresh water is 917/1000, so about 92% of the cube is below the surface.

  18. neutral buoyancy

    An object whose average density equals the fluid's, so it stays at any depth.

    Loses the mark: “it floats on the surface because it is neutral”. A neutrally buoyant object stays wherever it is placed, fully submerged.

    Example: The diver adjusts her vest until she has neutral buoyancy and hovers 5 m down.

  19. apparent weight in a fluid

    Units: N

    A submerged object's weight minus the buoyant force, as a scale reads.

    Loses the mark: “the rock lost 10 N of weight”. Its weight is still 30 N; the water pushes up with 10 N.

    Example: The rock weighs 30 N but its apparent weight in a fluid is 20 N, so the buoyant force is 10 N.

  20. third-law partner of the buoyant force

    The downward force an immersed object exerts on the fluid, equal to the buoyant force.

    Loses the mark: “the scale under the beaker reads the same”. The fluid pushes up on the block, so the block pushes down on the fluid and the scale.

    Example: Dipping the hanging block into the beaker raises the lower scale by 4 N, the third-law partner of the buoyant force.

  21. continuity equation

    A1v1=A2v2A_1v_1 = A_2v_2

    In steady incompressible flow, cross-sectional area times speed is the same at every section.

    Loses the mark: “narrower pipes slow the flow”. The same volume per second must pass a narrow section, so the fluid speeds up there.

    Example: By the continuity equation, halving the hose's area at the nozzle doubles the water's speed.

  22. volume flow rate

    Q=AvQ = Av · Units: m³/s

    The volume of fluid passing a cross-section each second, area times average speed, in m³/s.

    Loses the mark: “flow rate means how fast the water moves”. Flow rate is volume per second; speed is meters per second.

    Example: The tap's volume flow rate is 2 × 10⁻⁴ m³/s, so it fills the 10 L bucket in 50 s.

  23. incompressible fluid

    A fluid whose density stays constant whatever the pressure.

    Loses the mark: “air in the duct is always incompressible”. Gases compress noticeably at high speeds or pressure changes.

    Example: Treating water as an incompressible fluid, whatever enters one end of the pipe each second must leave the other.

  24. Bernoulli's equation

    P+12ρv2+ρgy=constantP + \tfrac12\rho v^2 + \rho gy = \text{constant}

    In steady incompressible frictionless flow, P + ½ρv² + ρgy is constant along a streamline.

    Loses the mark: “the fast air sucks the paper up”. There is no suction; the higher pressure below pushes the paper up.

    Example: By Bernoulli's equation, the water speeds up in the narrow throat, so its pressure there is lower.

  25. streamline

    The path traced by a small parcel of fluid in steady flow.

    Loses the mark: “compare the blown air with the still air in the room”. These are not on one streamline, so Bernoulli's equation does not connect them.

    Example: I compare the free surface and the outlet because the same streamline connects them.

  26. energy per unit volume

    Units: J/m³ = Pa

    Each term in Bernoulli's equation is an energy per unit volume, in J/m³.

    Loses the mark: “Bernoulli across the pump”. A pump adds energy, so the sum is not constant between points either side of it.

    Example: The term ½ρv² is the kinetic energy per unit volume of the moving water, 2 kJ/m³ at 2 m/s.

  27. ideal fluid

    A fluid with no internal friction that flows steadily and is incompressible.

    Loses the mark: “Bernoulli works for every real pipe”. Viscosity dissipates energy, so long pipes show pressure drops Bernoulli ignores.

    Example: Real water in a long hose is not an ideal fluid, so the pressure drops along the pipe even where the speed is constant.

  28. Torricelli's theorem

    v=2ghv = \sqrt{2gh} · Units: m/s

    Liquid leaves a small hole a depth h below the free surface at speed √(2gh).

    Loses the mark: “a bigger hole gives a faster jet”. The exit speed depends only on depth; a bigger hole raises the flow rate.

    Example: By Torricelli's theorem, water 0.8 m below the surface leaves the hole at √(2 × 9.8 × 0.8), about 4 m/s.

  29. jet as a projectile

    A liquid stream leaving a hole moves as a projectile launched horizontally.

    Loses the mark: “depth below the surface used for the fall height”. The fall height is the hole's height above the floor, a different length.

    Example: Treating the jet as a projectile, water leaving at 4 m/s from 1.25 m above the floor lands 2 m out.

  30. independent variable

    The quantity the experimenter deliberately changes to see its effect.

    Loses the mark: “the thing that stays the same”. That is a controlled variable; the independent variable is the one changed on purpose.

    Example: The independent variable is the pendulum length, set to 0.2, 0.4, 0.6, 0.8 and 1.0 m.

  31. dependent variable

    The quantity measured to see how it responds to changes in the independent variable.

    Loses the mark: “the variable I control”. The controlled or changed variable is not the one measured as a response.

    Example: The dependent variable is the period, timed over 10 swings for each length.

  32. controlled variable

    A quantity held fixed throughout an experiment so that it cannot explain the result.

    Loses the mark: “measure carefully and be accurate”. General care is not a design choice; name the quantity held fixed and how.

    Example: The release angle is a controlled variable, kept at 10° so that amplitude cannot affect the period.

  33. dimensional analysis

    Checking that every term of an equation has the same dimensions.

    Loses the mark: “kg m^2 s^-2 is wrong because it should be joules”. Those are the base units of a joule; the answer is consistent.

    Example: Dimensional analysis shows the pendulum period cannot depend on the bob's mass, since nothing else carries kilograms to cancel it.

  34. dimension

    The kind of quantity something is, such as length, mass or time.

    Loses the mark: “a dimension is the unit it is measured in”. Meters and miles are different units of one dimension, length; a conversion changes the unit, never the dimension.

    Example: Speed has the dimension of length divided by time, whether it is quoted in m/s or in mi/h.

  35. SI base units

    The defined units, including the meter, kilogram and second, from which others are built.

    Loses the mark: “grams and centimeters in the formula”. Mixing in non-SI units gives answers off by powers of ten.

    Example: In SI base units a newton is kg·m/s², so a spring constant in N/m is kg/s².

  36. unit conversion

    Multiplying by factors equal to one, such as 100 cm per 1 m.

    Loses the mark: “divide square centimeters by 100”. Area units convert with the square of the factor, so divide by 10,000.

    Example: The unit conversion from 20 cm² to m² divides by 100², giving 0.002 m².